- 7" LED Backlight Color TFT LCD monitor
- Full color LED backlight display.
- High-resolution picture.
- With 2 AV input.
- Comes with an IR remote controller.
Features:
7" LED Backlight Color TFT LCD monitor.
High-resolution picture.
Full color LED backlight display.
With 2 AV input.
AV1 connects to car DVD, VCR and other video equipment.
AV2 to car backup camera.
Parking rearview priority: The monitor will start up automatically, and synchronously display the video from rearview camera when you're backing your car; the monitor will close itself after backing. Scenes will cut to rearview camera automatically while you're backing the car and change back to the original scene after that.
Screen rotatable.
Screen ratio 16:9/4:3 adjustable.
Brightness/contrast/color adjustable.
2 ways to install: standing or mounting.
Low power consumption.
No Audio input or output.
Comes with an IR remote controlle
Precio de lista: $ 189.68
Precio: $ 20.00
More
Products
Good 7″ monitor for the money!,
The monitor is by no means a high resolution monitor, but it gets the job done and kids really do not care about the resolution so long as they can see the movie and subtitles if enabled, both of which are very usable on this monitor. If you need a cheap monitor for the kids, this will do just fine and it is cheap enough to replace should something happen to it.
0
Was this review helpful to you?
Wiring is self evident,
I purchased the package consisting of the monitor, the E363 camera and the Koolertron license plate camera. There is no comparison between the cameras, the E363 with 170 degree viewing angle wins. I have a 2007 Honda CRV and I mounted the camera low under the rear bumper and the view from the camera is just amazing. I then ran the wiring into the spare tire well and made my connections in that area. There is an ignition activated power outlet on the left rear wall that I used for the power source running everything all the time while driving. Snaking the single cable which contains the video signal and power wire up to the front was relatively easy, tucking the cable under the trim.
The monitor is very nice, I found the picture quite pleasing. I mounted it with nylon straps via the AC vent over my radio, which I never use. The single cable from the monitor is all that is required, it contains the wiring for the two video inputs and power, snaking it around was quite easy. It plugs into a longer harness that connects to the cable coming from the camera. The monitor has brightness and contrast controls along with the ability to flip the picture left or right, up or down so it accommodates the camera no matter what. As one might expect the monitor is always on, that is, anytime you turn the key it automatically comes on. You do not have to punch the on-off button every time.
Backing up at night is adequate because of the built in vehicle back up lights. The E363 camera has no infrared LED’s.
0
Was this review helpful to you?
Can’t beat it for the price but needs more info added to the included instructions about using with a backup camera,
Even after everyone else’s warnings about the inadequate instructions I wasn’t too concerned because it only has three wires to hook up (red, black and blue) besides plugging in your video source(s). What the included instructions do not tell you is that if you are connecting a backup camera it MUST be connected to the Video 2 plug in order to work with the blue wire to sense when you’ve shifted into reverse. It would have been so much easier if in the included instructions in the box they would have noted that «Video 2 input is for connecting a backup camera.» My backup camera had a female end so I could only plug it into Video 1 of the monitor and it would not work that way with the blue reverse trigger wire. After searching around I found the needed info back in the product’s description on Amazon. Why didn’t they include that info in the wiring instructions?
So, in short, to take advantage of the blue reverse sensing wiring the backup camera must be plugged into the monitor’s Video 2 input (the yellow female RCA plug). Red = Positive, Black = ground, Blue = Reverse trigger wire, Video 2 input = Camera…Wired like this it will turn on the monitor when you shift into reverse and off when you take it out of reverse.
0
Was this review helpful to you?